Distillation
10" Cold Trap with KF25 Ports
10” X 10” KF25 Cold Trap Kit Cold traps are used in vacuum applications where contaminating vapors may be present, and a cold trap is required to assure vapors are condensed before reaching the vacuum pump. They can be used with any pump but are mostly used with rotary vane pumps. Protecting your pump will greatly increase the life of all your seals and internal components it will also assure that a full vacuum is pulled based on the pump’s capabilities. BVV’s 10”X10” KF25 Cold Trap features 2 qty. KF25 ports. The lower port is connected to the system that is under vacuum and the top to the vacuum pump. The KF25 allows for a larger bore and works great for high flow applications. This kit comes with 2 qty. KF25 rings and 2 qty. KF25 clamps ready to be connected in line with your setup. The internal pot is stainless steel and can hold 1.5 gallons which will hold the dry ice slurry or other method of getting cold. A silicone O-ring sits around the 1.5-gallon pot and creates a seal with the top of the 10”X10” base. For more specifications, please view table and diagrams below. Product Information Sheet **This cold trap comes pre-tested to pull down to 30 microns** **This cold trap is rated for applications down to 30 microns. If your application requires a deeper vacuum, please DO NOT USE THIS COLD TRAP** Specifications Model CTRAP10X10-B Material of Base and Internal Pot Stainless Steel Gasket Material Silicone Lid Material Silicone + Glass Vacuum Rating 30 microns Weight 29lbs Overall Height 11.5” Overall Diameter (Including Ports) 14” Cold Trap Surface Area 234.45 sq.in Internal Pot Volume 1.5 gallons Chemical Compatibility with Glass Lid Ethanol Excellent Acetone Good Water Excellent Propylene Glycol Excellent Isopropyl Alcohol Excellent Chemical Compatibility with Silicone O-Ring and Lid Seal Ethanol Good Acetone Good Pentane Good Hexane Good Heptane Good View of 10” x 10” Cold Trap
$850.00
BVV PTFE Thermocouple Adapters
BVV PTFE Thermocouple Adapters BVV PTFE adapters are for use with either 1/8” or 1/4” thermocouples. The adapter has an outer Viton O-ring to form a grease-free, airtight seal between the adapter and the listed size of the outer joint. The compression nut works in conjunction with the upper Viton® to provide an airtight seal between the adapter and thermocouple. (Compare to Chemglass CG-1048-A Thermocouple Adapters.)
$25.00
Thermometer Adapter
Glass Thermometer Adapters Glass thermometer adapters are used in conjunction with 1/4" temperature probes, these adapters allow the user to maintain a vacuum on their glassware system while being able to have a consistent readout of the internal temperature of the system. These adapters have a puncture gasket to create the perfect seal around most temperature probes on the market. Joint Sizes Available: 14/20 Joint Size 24/40 Joint Size *Notice to customers: All units are inspected for broken glassware or parts before leaving BVV™. If the unit arrives damaged (this does not include minor imperfections or scuffs in glassware), the customer MUST contact BVV™ within 72 hours from carrier delivery to file a claim. If the customer DOES NOT contact BVV™ within 72 hours from carrier delivery, then BVV™ cannot issue any replacement(s) or compensation for the item; a new purchase will need to be made for a replacement. **Glassware Safety Disclaimer: BVV™ is not responsible for failure of glassware which must be inspected before and after every use because it may eventually develop imperfections or damage through normal usage, mishandling, and stress caused by temperature variations. If an imperfection or damage is noted while inspecting the glassware DO NOT use the glassware because it can fail causing bodily harm or damage to the surrounding area.**
$15.00 - $17.00
Male Hollow Stopper
Male Hollow Stopper Male Hollow Stoppers are used for capping off or plugging a female join to prevent contamination or close off a port on a glassware system. These glass stoppers are hollow on the inside and require vacuum grease to create a seal when having 2 ground surfaces touching in a vacuum application. Joint Sizes Available: 14/20 Ground Joint 24/40 Ground Joint *Notice to customers: All units are inspected for broken glassware or parts before leaving BVV™. If the unit arrives damaged (this does not include minor imperfections or scuffs in glassware), the customer MUST contact BVV™ within 72 hours from carrier delivery to file a claim. If the customer DOES NOT contact BVV™ within 72 hours from carrier delivery, then BVV™ cannot issue any replacement(s) or compensation for the item; a new purchase will need to be made for a replacement. **Glassware Safety Disclaimer: BVV™ is not responsible for failure of glassware which must be inspected before and after every use because it may eventually develop imperfections or damage through normal usage, mishandling, and stress caused by temperature variations. If an imperfection or damage is noted while inspecting the glassware DO NOT use the glassware because it can fail causing bodily harm or damage to the surrounding area.**
$5.00 - $10.00
Female Joint Stopper - 24/40
Female Joint Stopper - 24/40 This glass stopper features a cap design and a ground interchangeable taper outer joint, perfectly suited to fit a 24/40 ground inner joint. The frosted, precision-ground glass surfaces ensure a tight seal when properly greased, providing reliability and security for your laboratory needs. The female joint's taper allows it to seamlessly fit any glassware with a male joint of the same taper and outside diameter, as long as there is no interference with the attached apparatus.Crafted from high-quality borosilicate glass 3.3 using hand-blowing techniques, our joint stopper ensures durability and resilience. The heavy-wall design of the glass tubing used in its construction further enhances its strength and longevity, making it a reliable choice for your laboratory experiments and applications. *Notice to customers: All units are inspected for broken glassware or parts before leaving BVV™. If the unit arrives damaged (this does not include minor imperfections or scuffs in glassware), the customer MUST contact BVV™ within 72 hours from carrier delivery to file a claim. If the customer DOES NOT contact BVV™ within 72 hours from carrier delivery, then BVV™ cannot issue any replacement(s) or compensation for the item; a new purchase will need to be made for a replacement. **Glassware Safety Disclaimer: BVV™ is not responsible for failure of glassware which must be inspected before and after every use because it may eventually develop imperfections or damage through normal usage, mishandling, and stress caused by temperature variations. If an imperfection or damage is noted while inspecting the glassware DO NOT use the glassware because it can fail causing bodily harm or damage to the surrounding area.**
$10.00
Chemglass Adapter, Bushing
Chemglass Adapter, Bushing Chemglass Bushing style adapter having a lower standard taper inner joint and outer joint ground in the bore of the adapter. Adapters having a 10/18 or 10/30 outer member in the bore are used to insert thermometers into apparatus. __________________________________________________________________________________________ ***Glassware Safety Disclaimer: BVV™ is not responsible for failure of glassware which must be inspected before and after every use because it may eventually develop imperfections or damage through normal usage, mishandling, and stress caused by temperature variations. If an imperfection or damage is noted while inspecting the glassware DO NOT use the glassware because it can fail causing bodily harm or damage to the surrounding area.*** ***All units are inspected for broken glass or parts before unit is shipped. If unit arrives damaged or glass is broken (this does not include minor imperfections or scuffs in glassware), Customer MUST contact BVV™ within 3 days of delivery to file a claim and receive a replacement part. If customer DOES NOT contact BVV™ within 3 days of delivery responsibility for replacement parts falls on the customer and they must pay for replacement pieces
$32.00 - $33.00
24/40 Jointed Straight Adapter
24/40 Jointed Straight Adapter This straight inlet adapter allows the user to connect two female 24/40 jointed connections. The overall distance between the joints is 70mm. *Notice to customers: All units are inspected for broken glassware or parts before leaving BVV™. If the unit arrives damaged (this does not include minor imperfections or scuffs in glassware), the customer MUST contact BVV™ within 72 hours from carrier delivery to file a claim. If the customer DOES NOT contact BVV™ within 72 hours from carrier delivery, then BVV™ cannot issue any replacement(s) or compensation for the item; a new purchase will need to be made for a replacement. **Glassware Safety Disclaimer: BVV™ is not responsible for failure of glassware which must be inspected before and after every use because it may eventually develop imperfections or damage through normal usage, mishandling, and stress caused by temperature variations. If an imperfection or damage is noted while inspecting the glassware DO NOT use the glassware because it can fail causing bodily harm or damage to the surrounding area.**
$15.00
Non-Mercury Glass Thermometer with 10/30 Joint
Non-Mercury Glass Thermometer with 10/30 Joint This non-mercury glass thermometer has a 10/30 ground glass joint and is 14" long with a temperature range of -10°C to 250°C with 1 degree increments. This thermometer is made in Germany and is Serialized and Calibrated. *Notice to customers: All units are inspected for broken glassware or parts before leaving BVV™. If the unit arrives damaged (this does not include minor imperfections or scuffs in glassware), the customer MUST contact BVV™ within 72 hours from carrier delivery to file a claim. If the customer DOES NOT contact BVV™ within 72 hours from carrier delivery, then BVV™ cannot issue any replacement(s) or compensation for the item; a new purchase will need to be made for a replacement. **Glassware Safety Disclaimer: BVV™ is not responsible for failure of glassware which must be inspected before and after every use because it may eventually develop imperfections or damage through normal usage, mishandling, and stress caused by temperature variations. If an imperfection or damage is noted while inspecting the glassware DO NOT use the glassware because it can fail causing bodily harm or damage to the surrounding area.**
$99.00
4 Way Vacuum Manifold
4 Way Vacuum Manifold The Vacuum Manifold can be used in conjunction with any vacuum application. It allows the user to selectively choose where to apply vacuum pressure. It is available in 1/4" or 3/8" barb connections and is assembled using 304-grade stainless steel parts. Please refer to the following example applications: Rotary evaporator vacuum distribution Multiple vacuum chambers with a single vacuum pump Air inlet to a vacuum system ***Note: Vacuum Manifold is intended for use with vacuum pressure only. It is not rated for positive pressure.***
$150.00
Stainless Steel KF-25 x Glass Jointed Adapter
Stainless Steel KF-25 x Glass Jointed Adapter This Custom Built 304 Stainless Steel Adapter allows the user to adapt to a KF-25 high vacuum fitting to a 24/40 or 34/45 ground glass joint fitting to allow the user to connect a KF flanged laboratory grade vacuum pump.
$55.00 - $60.00
Stainless Steel 24/40 x 1.5" Tri-Clamp Adapter
Stainless Steel 24/40 x 1.5" Tri-Clamp/ Tri Clover Adapter This Custom Built 304 Stainless Steel Adapter allows the user to adapt to a 24/40 ground glass joint to a 1.5" Tri-Clamp fitting to allow the user to connect the glass joint to a Tri-Clamp system.
$55.00
Stainless Steel Tri-Clamp x Female Joint Adapter
This unique adapter allows the user to adapt a Tri-Clamp fitting to a male ground joint glass fitting and it is made out of 304 stainless steel.
$30.00
KF High Vacuum Stainless Steel Flange x Female Joint Adapter
This unique adapter allows the user to adapt a KF25 or KF40 High Vacuum Flange fitting to a male ground joint glass fitting and it is made out of 304 stainless steel.
$30.00 - $34.00
BVV Lab Stand
Metal-Base Lab Stand This lab stand has a metal base that measures 5.5" x 7-3/4" x 7/8" and the rod comes in two heights: 24 and 36 inches. It also has 2 pre-threaded holes that are in the center and near the edge of the base to allow multiple positions when attaching the rod.
$45.00 - $50.00
Lab Stand Lattice Support
Lab Stand Lattice Support This Lab Stand Lattice Support easily lets the user adjust and customize their height according to their application and has 3 metal bases, 6 offset boss heads, (2) 36" horizontal rods and either 24" (standard) or 36" upgraded vertical rods selected through a drop down.
$210.00 - $222.00
Threaded Lab Stand Rod
Stainless Steel Threaded Rod 10 x 1.5mm Thread, 0.50 Diameter rod, and is 24" in length and can be used as extra lattice supports in a any application.
$10.00 - $15.00
3 Finger Clamp Adjustable 0-70mm
3 Finger Clamp Adjustable Up to 70mm 3 Finger Clamp has an adjustable diameter of up to 70mm. Ideal for holding workpieces, lab equipment, beakers, flasks, flashlights, webcams, etc. Three-finger clamps are used to hold larger pieces of glassware.
$15.00
Chain Clamp
Chain Clamp Chain clamp for use with tripod stands or other laboratory stands. Allows user to secure large diameter glassware, such as glass cold traps, to tripod or laboratory stands using boss head clips. Specifications: Chain Length = 15" Spring Loaded Tensioner Rod Length = 8.5" Rod Diameter = .475"
$21.00
Ring Support with Boss Head
Ring Support with Boss Head This Support Ring with bosshead allows the user to easily add much-needed support to round glassware or conical like a separatory funnel. The support opening measures 2.5" in diameter and has an overall length of 8-1/4".
$17.00
Boss Head - 16mm
Boss Head - 16mm This Boss head is made out of Die-Cast alloy and has nickel plated Wing Screws and will fit rod diameters up to 16mm.
$10.00
Swivel Bosshead
This swivel boss head is made out of die-cast alloy is nickel plated and will fit rod diameters up to 16mm. The boss head can be adjusted and locked to any angle (360°). It is also designed to carry heavy loads and prevent torque damage. Note:Clamps and rods are NOT included.
$11.00
chemglass Clamp Holder, Premium Offset Boss Head
Clamp Holder, Premium Offset Boss Head Nickel-plated zinc alloy clamp holder is ideal for holding clamps to lab frames. Use wherever clamping at 90° is required. Maximum rod grip size is 18mm.
$25.00$10.00
Boss Head - Double Swivel
Boss Head - Double Swivel Made of high strength powder coated alloy and can support up to 16mm rods. The boss head can be adjusted and locked to any angle (360°). It is also designed to carry heavy loads and prevent torque damage. Furthermore, it has three wide pad metal screws to easily secure itself to a clamp and support apparatus. Note:Clamps and rods are NOT included.
$11.00
Table Clamp for Supporting Lattice
Table Clamp for Supporting Lattice This Table Clamp for supporting lattice can easily hold up to 12mm diameter rods.
$12.00
2 Pack Metal Keck Clips - 34/45
2 Pack Metal Keck Clips - 34/45 Stainless steel clamps to fit 34/45 standard taper joints. Metal clamps are suitable for high temperatures applications
$10.00
2 Pack Metal Keck Clips - 45/50
2 Pack Metal Keck Clips - 34/40 Stainless steel clamps to fit 45/50 standard taper joints. Metal clamps are suitable for high temperatures applications
$10.00
5 Pack of Metal Keck Clips for 24/40 Joints
5 Pack of Metal Keck Clips for 24/40 Joints 5 Pack of Metal Keck Clips for 24/40 joints. Universal clips for ground joints manufactured from high-grade stainless steel. These clips fit snugly and are not overly difficult to slide on and off.
$10.00
5 Pack of Plastic Keck Clips for 24/40 Joints
5 Pack of Plastic Keck Clips for 24/40 Joints 5 Pack of Plastic Keck Clips for 24/40 joints.
$7.50
GL-14 Cap
GL-14 Cap This GL-14 cap is used for sealing off GL-14 connections or venting vacuum in a system without the use of a valve. Gasket not included. (Note: Only 1 cap included. Increase quantity to order more caps.)
$5.00
Solid Cap, PTFE Seal, GL-14 Thread
Cap is made from PBT (thermoplastic polyester) and will withstand temperatures from -45 to 200º C. The seal is PTFE
$4.00
Magnetic PTFE Stir Bar Retriever
Magnetic PTFE Stir Bar Retriever Magnetic PTFE Stir Bar Retriever is used to retrieve the stirring bar from a boiling flask. Specifications: 400mm Length Material: High Temperature PTFE
$24.00
Magnetic PTFE Stirring Bar - L Style - 70mm
Magnetic PTFE Stir Bar - L Style - 70mm Reduce stir bar jumping with the contoured shape of this L Style Magnetic PTFE Stir Bar. Ideal for round-bottom flask stirring applications. This 70mm L Style Magnetic Stir bar is great for round-bottom flasks above 5 liters in capacity. With its PTFE coating this Magnetic Stir Bar carries excellent solvent and temperature compatibility for a variety of applications. Specifications: L Style 70mm Length Material: High-temperature PTFE
$25.00
2 Pack Magnetic PTFE Stirring Bar - B Style - 28mm
2 Pack Magnetic PTFE Stirring Bar - B Style - 28mm 2 Pack of Magnetic PTFE Stirring Bar. Specifications: B Style 28mm length Material: High temperature PTFE Quantity: 2
$16.00
2 Pack Magnetic PTFE Stirring Bar - B Style - 40mm
2 Pack Magnetic PTFE Stirring Bar - B Style - 40mm 2 Pack Magnetic PTFE Stirring Bar Specifications: B Style 40mm Length Material: High temperature PTFE Quantity: 2
$16.00
2 Pack Magnetic PTFE Stirrer - L Style - 28mm
2 Pack Magnetic PTFE Stir Bar - L Style - 28mm Shop this 2 Pack Magnetic PTFE Stirring Bar to stir liquids in a closed container on BVV™! Used in short-path distillation. Find product details below. Specifications: L Style 28mm Length Material: High-temperature PTFE Quantity: 2
$15.00
2 Pack Magnetic PTFE Stirring Bar - HL Style - 25mm
2 Pack Magnetic PTFE Stirring Bar - HL Style - 25mm 2 Pack Magnetic PTFE Stirring Bar Specifications: HL Style 25mm length Material: High temperature PTFE Quantity: 2
$16.00
PTFE WFE Wipers - 3 Pack
PTFE WFE Wipers These wipers are designed for wiped film evaporators spinning counterclockwise. Pack of 3 Dimensions: 15.375L x .38W x .42D
$350.00
Tool-Less Adapter Assembly
Tool-Less Adapter Assembly This adapter fits on 30mm OD glass flanges. The other side is 1/2" MNPT to connect to various fittings for attaching hoses and like items.
$100.00
Beaker Tongs
Beaker Tongs These beaker tongs are great when handling any glassware that is too hot to handle or off-gassing and allows the user to handle the beaker at a safe distance with ease. These tongs are a 3 finger design with nickel plated metal and rubber coated fingers with an overall length of 10.5".
$10.00
Flask Tongs
Flask Tongs These flask tongs are great when handling any glassware that is too hot to handle or off-gassing and allows the user to handle the flask or beaker at a safe distance with ease. These tongs are a 2 finger design with nickel plated metal and rubber coated fingers with an overall length of 10.5".
$6.00
BVV Brewing 4" Copper Sight Glass Union Tri-Clamp Tee
BVV Brewing 4" Copper Sight Glass Union Tri-Clamp Tee 4" Copper Sight Glass Union Tri-Clamp Tee 4"x 4"x 3",Distillation Lens Column For Home Brewing ,Length 150mm. Specifications Material Red Copper/Stainless Steel Connection method: Clamp Connection Pipe size: 4" Surface treatment Mirror Surface Medium Oil Chemical industry water conservancy electric power boiler, machinery metallurgy sanitary construction etc.
$200.00$125.00
BVV Brewing Copper Bubble Cap Plate
BVV Copper Bubble Cap Plate Copper Bubble Cap Plate. These copper bubble plates are used in a flute still column positioned between sections to help with separation of alcohol and waters. The alcohol water bubbles up on the plates allowing the distiller to see the action happening in the still column. More bubble cap plates in a column and a taller column with a reflux condenser or dephleg create a high percentage neutral spirit. Copper bubble plates can be taken apart and cleaned with citric acid or mild acid solution. Sizes Available 4" 99.9% Red Copper bubble plate 6" 99.9% Red Copper bubble plate
$35.00 - $115.00
BVV Brewing Whiskey Helmet
BVV Brewing Whiskey Helmet The Whiskey Helmet, onion Head comes comes with a 1/2npt Thermo connection. Traditional whisky helmets help to blend vapors and produce a better quality products. Can work with a reflux column or as a part of pot still. Copper naturally aids the distillation, the helmet will help remove the unwanted things in alcohol vapor and bring more flavor to your final product. Sizes Available 4" x 4" Whiskey Helmet , Onion head 11L (approximately), Pure Copper 99.99% 6" x 6" Whiskey Helmet , Onion head 30L (approximately) , Pure Copper 99.99%
$700.00$400.00
BVV Brewing SS304 Parrot
BVV Brewing SS304 Parrot SS304 Parrot w 3/4" TC Drain Port High quality product collector (also known as parrot or parrot body) made of stainless steel. This essential part of a still can easily be mounted with tri-clamps. Shape and angle of the product outlet take care of a clean fluid friction directly into a collection jar or funnel. Specifications Material: Stainless Steel Weight 1.10 Height 10.11-inch Connection 1 3/4 " Tri-Clamp Connection 2 3/4 " Tri-Clamp (with 3/8" bore)
$150.00$60.00
Chemical-Resistant Viton® Fluoroelastomer O-Ring
Chemical-Resistant Viton® Fluoroelastomer O-Ring 1/16 Fractional Width, Dash Number 006
$0.95
Double Neck Round Bottom Flask
Double Neck Round Bottom Flask Double Neck Round Bottom Flasks can be used for a variety of applications such as capturing and collecting material and also used for boiling off material through distillation. These flasks are double neck with a ground 24/40 joint and require the application of vacuum grease to the ground surface when using the flasks in a vacuum application. The second neck of this flask can also be used for a thermometer port or for introducing material into the flask with a glass funnel. When laying these flasks down it is always recommended to use a cork stand for the flask to prevent breakage and keep the flask upright. Sizes Available: 500ml - 24/40 Ground Joint 1000ml - 24/40 Ground Joint 2000ml - 24/40 Ground Joint *Notice to customers: All units are inspected for broken glassware or parts before leaving BVV™. If the unit arrives damaged (this does not include minor imperfections or scuffs in glassware), the customer MUST contact BVV™ within 72 hours from carrier delivery to file a claim. If the customer DOES NOT contact BVV™ within 72 hours from carrier delivery, then BVV™ cannot issue any replacement(s) or compensation for the item; a new purchase will need to be made for a replacement. **Glassware Safety Disclaimer: BVV™ is not responsible for failure of glassware which must be inspected before and after every use because it may eventually develop imperfections or damage through normal usage, mishandling, and stress caused by temperature variations. If an imperfection or damage is noted while inspecting the glassware DO NOT use the glassware because it can fail causing bodily harm or damage to the surrounding area.**
$25.00 - $50.00
High-Temp GL to Stainless Steel Tube Stub
High-Temp GL to Stainless Steel Tube Stub High-Temp GL to Stainless Steel Tube Stub allows the user to connect a compression fitting or flexible tubing to the adapter and withstand higher temperatures than a normal polypropylene GL adapter. Specifications: 1/4" or 3/8" OD Stainless Steel Tube Stub GL14 or GL18 Female Connection Straight Style 150°C or 250°C Low Temp/High Temp GL Adapter
$21.00 - $30.00
KF-25 Ground Joint PTFE Adapter
KF-25 Ground Joint PTFE Adapter This adapter will fit any standard 24/40 or 34/45 ground glass joints and adapt to a KF25 flange. This adapter is best used to hook up a glass system to a steel vacuum hose such a KF25 bellows. The Joint has an o-ring for better sealing, but vacuum grease is still recommended for the best connection.
$25.00
You have seen 96 out of 97 products